Panasonic VF200 Instruction Manual Download Page 174

Page: 174 / 289

Appendix Function Parameter List

P026

Waiting Time

Waiting time required by the start mode, the ride-through restart and retry

function can be set.

Data setting range (s) 0.1 to 100.0

Related parameters: P022 to P025

P027

Reverse Run Lock

When used only in forward run mode, reverse run can be disabled to avoid

possible mishandling.

Setting value

Details

Reverse run operation enabled

(Both forward run and reverse run

operation enabled)

Reverse run disabled

(Only forward run operation enabled)

・

When disabled, reverse run cannot be performed during the operation of

panel, external control and communication.

Related parameter: P004

P028

Stop Mode

Ramp-to-stop or coast-to-stop mode can be selected when stopping the

inverter.

Setting value

Mode

Details

Ramp-to-stop

The inverter is stopped by the stop signal

depending on the frequency decreased according

to the deceleration time.

Coast-to-stop

The inverter output is shut off immediately by the

stop signal.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands