Panasonic VF200 Instruction Manual Download Page 61

Page: 61 / 289

4. Operation Method (Basic Operation)

4.7 Operating with Operation Panel

When the inverter is operated with operation panel, as shown in “4.5 Setting

Frequency with Operation Panel” and “4.6 Setting Forward/Reverse Run with

Operation Panel”, there are 4 combined modes by using parameters “P003: Run

Command Select” and “P004: Frequency Setting Signal”.

This section will describe the four operation modes through specific examples.

Parameter P004: “Frequency Setting Signal”

Setting value “0”

Setting value “1”

Setting value “0”

Operation mode 1

Operation mode 3

Parameter P003:

“Run Command

Select”

Setting value “1”

Operation mode 2

Operation mode 4

■

Operation status when the panel is removed during operation

Sometimes OP trip will not occur if the operation panel is removed during

operation.

Item

Conditions of OP

trip occurrence

Conditions of OP trip

non-occurrence

Setting values of

“P003: Run

Command Select”

and “P004: Frequency

Setting Signal”

P003 = 0 or 1

P004 = 0

P003 is set to a

value greater than “2”

and

P004 is set to a value

greater than “1”.

Inverter operation

status when the panel

is removed during

operation

Operation stops

due to OP trip

occurrence.

Operation continues.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands