Panasonic VF200 Instruction Manual Download Page 228

Page: 228 / 289

Appendix Function Parameter List

221

・

When frequency setting signal is set with digitial or communication method,

the inverter will not perform 0 V stop.

・

If frequency setting signal is lower than 1/100 (1%) of full scale, the

command value will become 0 Hz.

Related parameters: P004, P099, P125

P102

P103

P104

Bias/Gain Function Select
Bias Frequency Setting
Gain Frequency Setting

The relationship between output frequency and frequency setting signal

(frequency setting analog signal of control circuit terminal No.14 or

potentiometer) can be adjusted freely. Please use this function according to

the applications.

■

Parameter P102: Bias/Gain Function Select

Setting

value

Details

Without bias/gain function

With bias/gain function

■

Parameter P103: Bias Frequency Setting

Data setting range (%)

－

99.0 to 250.0

■

Parameter P104: Gain Frequency Setting

Data setting range (%) 0.0 to 500.0

・

Bias frequency and gain frequency are set with the ratio (%) of 100%

maximum output frequency (parameter P008).

・

The frequency exceeding the maximum frequency or the upper frequency

limit will not be output.

Also, the frequency will not drop below the lower frequency limit.

・

The inverter will not perform reverse run operation even if negative

frequency setting signal is input.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands