Panasonic VF200 Instruction Manual Download Page 59

Page: 59 / 289

4. Operation Method (Basic Operation)

4.6 Setting Forward/Reverse Run with
Operation Panel

There are 2 modes to set forward/reverse run with operation panel as follows.

■

Forward/Reverse Run Button Operation Mode (Parameter P003 is set to “1”.)

Press UP (forward run) button or DOWN (reverse run) button on the panel to

select the rotation direction. Then press RUN button to start operation.

* The inverter will not run just by pressing RUN button.

* The “MOP function” cannot be used if frequency setting is made in “Digital

Setting Mode”.

■

Rotation Direction Setting Operation Mode (Parameter P003 is set to “0”.)

In Operation Status Display Mode, press MODE button twice to enter Rotation

Direction Setting Mode. Press SET button to display the rotation direction data,

change the rotation direction with UP and DOWN buttons, and then press SET

button again to apply the change. (The factory setting is “forward run”.)

Finally, press RUN button to start operation.

Run

command

Display

Rotation

direction

Display

Operation

panel

Forward

run

External

control

Reverse

run

Communication

Current

status

Display

Rotation

direction

Display

During

stop

Forward

run

During

forward

run

Reverse

run

During

reverse

run

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands