Panasonic VF200 Instruction Manual Download Page 104

Page: 104 / 289

7. Custom Mode

6. Press

button to complete allocation of parameter No.

Initial settings of custom parameters No.1 to No.10 are shown in the following

table.

Custom parameter

No.

Function Parameter

No.

Function name

Initial

value

Reference

page

U001 P001

The 1

Acceleration

Time

5.0

P.142

U002 P002

The 1

Deceleration

Time

5.0

P.143

U003 P007

Torque Boost

P.153

U004 P003

Run Command Select

P.144

U005 P004

Frequency Setting

Signal

0 P.146

U006 P008

Max. Output Frequency

50.0 P.155

U007 P009

Base Frequency

50.0 P.155

U008 P145

Operation Status

Monitor

0 P.259

U009 P147

Alarm LED Operation

Select

0 P.260

U010 P150

Password

0000 P.262

To restore the initial settings of allocated custom parameters No.1 to No.10,

please set the function parameter “P151: Setting Data Clear” to “3”. (The data

is not changed.)

Since all the allocated contents to custom parameters are stored in operation

panel, they will remain valid even if the panel is removed and connected to

other inverters.

All data, except those that can be changed during operation, can only be

monitored during operation.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands