Panasonic VF200 Instruction Manual Download Page 274

Page: 274 / 289

Appendix Function Parameter List

267

P157

The 2

Analog Superimposed Value

Bias value can be superimposed to the 2

analog input value with this

parameter.

Name

Setting range

The 2

Analog

Superimposed

Value

－

100.0% to

＋

100.0%

Related parameters: P124, P126 to P127

For setting method, please refer to “P124: The 2

Analog Input Function

Select”.

P158

The 2

Motor Capacity

・

During vector control or when auto torque boost or slip compensation is

performed through V/F control, inverter capacity used to drive the motor can

be set.

Related setting values are the same as the those of 1

motor. Please refer to

parameter “P130: Motor Capacity”.

If data is changed, the setting values of parameter “P160: The 2

Voltage

Compensation Constant” and “P161: The 2

Slip Compensation Frequency”

will be automatically changed to motor constants recommended by our

company.

P159

The 2

Motor Pole Number

・

During vector control or when auto torque boost or slip compensation is

performed through V/F control, pole number required to drive the motor can

be set.

Related setting values are the same as the those of 1

motor. Please refer to

parameter “P131: Motor Pole Number”.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands