Panasonic VF200 Instruction Manual Download Page 33

Page: 33 / 289

3. Wiring

3.1 Safety Precautions

Make sure that power is turned OFF before starting

wiring.

Failure to do so may result in an electric shock or fire.

Always connect ground wire.

Failure to do so may result in an electric shock or fire.

Wiring work should always be carried out by qualified

electrician.

Failure to do so may result in an electric shock or fire.

Always install the unit before wiring.

Failure to do so may result in an electric shock or injury.

Do not connect an AC power source to output terminals

(U, V, W).

Failure to do so may result in injury or fire.

Make sure that the voltage rating of the product

matches with that of AC power source.

Failure to do so may result in injury or fire.

Tighten the terminal screws to the specified tightening

torque.

Failure to do so may lead to fire.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands