Panasonic VF200 Instruction Manual Download Page 278

Page: 278 / 289

Appendix Function Parameter List

271

P168

Upper Frequency Limit Select for Speed Search

Frequency range for speed search can be set with this parameter.

Details

Speed search is performed
below the maximum frequency.

Speed search is performed at
the frequency lower than the
previous frequency before the
operation is stopped normally.

P169

Winding Mode Control Select

Whether winding mode control is selected or not and the amplititude during
such control can be set with this parameter.

Details

Winding mode control is OFF.

Amplititude is set based on the
setting frequency.

Amplititude is set based on the
maximum frequency.

P170

Amplitude in Winding Mode

Frequency amplititude under winding mode control can be set with this

parameter.

When P169 = 1, frequency amplitude (Hz) = setting frequency (Hz)

amplitude in winding mode (%)
When P169 = 2, frequency amplitude (Hz) = maximum frequency (Hz)

amplitude in winding mode (%)
For details of winding mode control, refer to P162.

Setting value

Setting range

（

）

0.0% to 100.0 %

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands