Panasonic VF200 Instruction Manual Download Page 124

Page: 124 / 289

9. Troubleshooting

9.2.2 Resetting Fault Trips

If the abnormality indicator in the display part of operation panel lights up and

operation is stopped, please handle the abnormality before resetting operation.

Reset by

power

The reset can be made by cutting off the power once.

(The inverter can operate when powered on again.)

Reset by stop

signal

1 For the operation in panel setting mode (parameter P003 is set to “0” or

“1”), press STOP button on operation panel to reset, and then restart the

inverter.

2 For the operation in external control mode (parameter P003 is set to “2” or

“3”), turn off OPERATION COMMAND button designed for external

control once to reset, and then restart the inverter.

Note) Reset by stop signal cannot be made through communication.

Reset by panel

For the operation in external control or communication setting mode

(parameter P003 is set to “4”, “5” or “7”), the reset cannot be made even if

OPERATION COMMAND button designed for external control or

communication is turned OFF once.

Press STOP button on operation panel to reset, and then restart the

inverter.

Reset by

multi-function

terminal

When parameter P036 to P040 are set to “1”, turn the function setting

switch ON once and OFF again to perform the reset.

Then restart the unit again.

Reset by

communication

command

Write 0x9696 into register No. 253 (DT253) to reset the inverter.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands