Panasonic VF200 Instruction Manual Download Page 73

Page: 73 / 289

4. Operation Method (Basic Operation)

5. Start forward run operation at operating frequency of 50

Hz.

Press

button.

Press

button.(The display part is flickering.)

Press

／

button to make value “50.0 (Hz)”

appear on the display. (The display part is flickering.)

Press

button to set operating frequency.

6. Stop operation.

Press

button. The motor starts to decelerate till to

stop.

7. Start reverse run operation at operating frequency of 50

Hz.

Press

button to select reverse run.

8. Start operation.

Press

button.

Since the frequency has been set to 50 Hz, the motor

will start to rotate counterclockwise at 50.0 Hz.

9. Switch reverse run to forward run during operation.

Press

button to select forward run.

10. Start operation.

Press

button.

The motor gradually decelerates and starts forward run

operation at 50 Hz again.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands