Panasonic VF200 Instruction Manual Download Page 87

Page: 87 / 289

5. Control Status Monitor

n024
n025

Unit Version
Panel Version

They show the firmware versions of VF200 unit and operation panel.

n026

Pulse Input Signal Detection Value

Display frequency detection value for pulse input signal of inverter.

n027

Winding Length

It is used for the calculate result for winding length of pulse input signal when

the setting vale for "P036:SW1 Function Select" is 14.

・

The calculate result of winding length is as follow.

・

The relation of winding and display is as follow.

When 1m to 9,999m, display as 1 to 9999.
When 10,000m to 99,999m, display as 10.00 to 9.999.
When 100,000m to 600,000m, display as 10.00 to 60.00.

・

If set value of "P038:SW3 Function Select" as 14, the calculate value will be

cleared when SW3 is ON.

The model code and version code are shown as follows.

About the version of VF200 unit and operation panel

Operation status display varies depending on the combination of firmware

version of VF200 unit and operation panel.

Combination of firmware

versions

Operation

VF200 unit firmware version >

operation panel firmware
version (VF200 unit version
Ver.1.0X excluded)

“Er2” will be displayed on the operation panel.

Press “

↑

” button to display VF200 unit firmware version.

Press “

↓

” button to display the operation panel firmware

version.

VF200 unit firmware version

≤

operation panel firmware
version

The version will be displayed as shown in the above figure.

Winding Length=

(pulse value input to SW1)×(P181: Winding length radio)

1000

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands