Panasonic VF200 Instruction Manual Download Page 234

Page: 234 / 289

Appendix Function Parameter List

227

3. Setting value (SP)

・

Setting signal of setting value (SP) is set with

parameter P004 (Frequency Setting Signal).

(Note) When Parameter P004 = “1” or “7”,

setting value (SP) is set with parameter P111

(PID Targert Value).

・

The relationship between setting signal and

setting value (SP) is set with parameter P102

to P104 (Bias/Gain Function Select, Bias

Frequency and Gain Frequency Setting).

<Example> 0 V = 0%, 5 V = 100%

4. PID operation mode select

・

PID operation mode is selected with parameter P106 (PID Control Mode).

5. Proportional gain (Kp), integral time (Ti), derivative time (Td) and control

cycle (Ts) settings

・

Coefficients (Kp, Ti and Td) used in PID control are set with parameter

P107 to P109.

* Automatic tuning function can be used to adjust coefficients (Kp, Ti and

Td) and change setting values.

・

PID control cycle (Ts) is set with parameter P110.

*The lower/upper limit of output frequency is set with parameter P099 and

P100.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands