manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 85

5

Unpacking and Installing

This section applies to AURICAL Aud as well as to the various accessories available. If the accessories are not part of your
configuration, disregard the instructions relating to the accessories.

To install and get started with AURICAL Aud and the OTOsuite Audiometry Module, follow the sequence below:
•

Install OTOsuite on the PC before you connect to AURICAL Aud from the PC.

•

Unpack AURICAL Aud (see

Unpacking

►

86

).

•

Assemble AURICAL Aud (see

Assembling AURICAL Aud

►

93

).

•

Connect the cables of the test equipment. See

–

Desktop or wall installation

►

94

–

AURICAL speaker unit installation

►

95

•

Run the OTOsuite Configuration Wizard to connect to and set up communication with AURICAL Aud. (See

Configuring

the Audiometry Module

►

101

.)

5.1

Requirements to the location

A sound cabin or sound treated room is not necessary, but it is recommended that you use a room where reverberation
time is not too long.

To ensure safe performance, AURICAL Aud must be correctly installed and the requirements listed in

Standards and

Safety

►

115

and

Technical specifications

►

119

must be complied with.

Warning

•

The charger unit should be kept away from the client area.

Warning

•

Keep AURICAL Aud away from all liquids and sources of heat (for detailed specifications, see

Oper-

ating environment

►

126

).

Warning

•

It is recommended to install the unit in an environment that minimizes the amount of static electricity.

For example, anti-static carpeting is recommended.

5.1.1

Requirements to noise in the test environment

Audiometry testing does not require a quieter testing environment than do other traditional Real Ear Measurement sys-
tems.

Although Audiometry testing is designed for use in a regular dispensing office environment, the test environment should
in some cases be adapted to suit the specific test types.
•

Make sure that the test environment is as quiet as possible. The quieter the room is, the more accurate your testing
will be.

It is very important that the measurements are not influenced by sounds or noise relating to anything else than the
presented test signals. Measurements of peak levels will be influenced by any sounds louder than the presented test
signals. Even extremely brief sounds may impact the measurements.

It is therefore important that the environment is well controlled to prevent any unforeseen influence.

•

Check that testing is not being done under an air conditioner or in front of a fan or ventilator.

Otometrics - AURICAL Aud

85

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands