manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 10

Speaker unit

Users: audiologists, hearing instrument dispensers and other health care professionals.

Use: The AURICAL speaker unit is intended to present audio signals for use with AURICAL Aud and the Audiometry mod-
ule, with AURICAL FreeFit and the OTOsuite PMM module and the OTOsuite Counseling and Simulations module.

1.6

About this manual

This is your guide to installing, calibrating and using AURICAL Aud and to using the OTOsuite Audiometry Module. It also
introduces you to the key features of the device and the software, as well as to working scenarios for performing tests and
viewing and printing test results.

We strongly recommend that you read this manual carefully before using AURICAL Aud and the Audiometry Module for
the first time.

Note

•

If you are using the Audiometry Module with NOAH, we recommend that you are familiar with the screens

and functions provided in NOAH.

1.6.1

Installation and assembly

Unpacking

►

86

and

Assembling AURICAL Aud

►

93

contain a full description of unpacking instructions and how to

assemble the device. For instructions on installing the software, see the OTOsuite Installation Guide.

1.6.2

Safety

This manual contains information and warnings which must be followed to ensure the safe performance of AURICAL Aud.

Warning

•

Local government rules and regulations, if applicable, should be followed at all times.

Safety information is stated where it is relevant, and general safety aspects are described in

Standards and Safety

►

115

.

1.6.3

Training

It is recommended that you read this manual and try out test scenarios before you start operating AURICAL Aud so that
you are familiar with both the device and the software program before testing a patient.

1.7

Typographical conventions

The use of Warning, Caution and Note

To draw your attention to information regarding safe and appropriate use of the device or software, the manual uses pre-
cautionary statements as follows:

Warning

•

Indicates that there is a risk of death or serious injury to the user or patient.

10

Otometrics - AURICAL Aud

1 Introduction to AURICAL Aud

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands