otometrics AURICAL Aud Reference Manual Download Page 18

Page: 18 / 136

When is masking required?

Masking is recommended when the following conditions are met:

AC > ACc + Min IA

AC > BCc + Min IA

BC < AC - x* dB

Only stored thresholds measured without masking are checked. Levels which did not evoke a response are excluded from
the check. This means that as soon as a masked threshold has been stored, the flashing stops for that frequency.

* denotes configurable Air/Bone gap criterion (

Tools

Configuration Wizard

Audiometry

Configure

... >

Masking

Assistant

Min IA is frequency specific

These are the Min IA tables for TDH-39 and Otometrics Inserts used in the Masking Assistant

Min IA (supraaural phone: TDH-39), frequency specific

125

Katz & Lezynski, (2002)

250

Munro & Agnew, BJA (1999)

500

Munro & Agnew, BJA (1999)

750

N/A - fulfill traditional approach

1000

Munro & Agnew, BJA (1999)

1500

N/A - fulfill traditional approach

2000

Munro & Agnew, BJA (1999)

3000

Hall J.W. III & Mueller G.H. III / Munro & Agnew, BJA (1999)

4000

Katz J / Munro & Agnew, BJA (1999)

6000

Hall J.W. III & Mueller G.H. III / Munro & Agnew, BJA (1999)

8000

Katz J / Munro & Agnew, BJA (1999)

Min IA insert phone

125

N/A - traditional value

250

Munro & Agnew, BJA (1999)

500

Munro & Agnew, BJA (1999)

1Katz, J., Lezynski, J. (2002). Clinical Masking. In J. Katz, ed.,

Handbook of Clinical Audiology

, Williams and Wilkins, Bal-

timore. Munro, K.J., Agnew,

N. A comparison of inter-aural attenuation with the Etymotic ER-3A insert earphone and

the Telephonics TDH-39 supra-aural earphone

. Br J Audiol 1999; 33: 259-262. Hall, JW., MUELLER, HG. (1997).

The audi-

ologists’ desk reference

, Volume I., Singular Publishing Group, San Diego.

Otometrics - AURICAL Aud

2 Navigating in the OTOsuite Audiometry Module

Summary of Contents for AURICAL Aud









































































































































Search results

Summary of Contents for AURICAL Aud

Reviews:

Brands by name

Popular brands

otometrics AURICAL Aud, Reference Manual

Search results

Summary of Contents for AURICAL Aud

Reviews:

Brands by name

Popular brands