manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 116

Direct connectors

•

All connectors within the red frame are connected directly to patient transducers.

Fig. 1

Sockets with direct connections to patient transducers - AURICAL Aud connection panel

Isolated connectors

•

All connectors within the red frame are isolated from patient transducers.

Note

•

The safety standards listed in

Standards and Safety

►

115

do not apply to the isolated connectors used in

the AURICAL Aud audiometer.

Fig. 2

Connectors isolated from patient transducers - AURICAL Aud connection panel

12.2.2

General warning notes

Warning

•

For warning notes applying to the AURICAL speaker unit charger when in use with AURICAL FreeFit,

see the warning notes in the AURICAL FreeFit Safety section in the AURICAL FreeFit documentation.

1. This class of equipment is allowed in domestic establishments when used under the jurisdiction of a health care pro-

fessional.

2. AURICAL Aud is intended for diagnostic and clinical use by audiologists and other trained health care professionals in

testing the hearing of their patients.

3. To prevent cross-infection, use new eartips when you test the next client.

4. Accidental damage and incorrect handling can have a negative effect on the functionality of the device. Contact your

supplier for advice.

5. For the sake of safety and in order not to void the warranty, service and repair of electro-medical equipment should

be carried out only by the equipment manufacturer or by service personnel at authorized workshops. In case of any
defects, make a detailed description of the defect(s) and contact your supplier. Do not use a defective device.

116

Otometrics - AURICAL Aud

12 Standards and Safety

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands