otometrics AURICAL Aud Reference Manual Download Page 99

Page: 99 / 136

5.8.3

Mounting AURICAL Aud on the AURICAL speaker unit

1. Click AURICAL Aud onto the mounting

plate on the rear of the AURICAL speaker
unit.

5.9

Powering AURICAL Aud

AURICAL Aud is powered through an external power supply connected directly to the mains outlet.

Switching on AURICAL Aud

Use only the power supply specified in Technical Specifications,

Power supply

►

127

1. Connect the mains plug of the external power supply directly to an AC mains outlet with a three-wire

protective ground.

2. Switch on the mains supply.

3. The On/Off indicator on AURICAL Aud lights green.

AURICAL Aud

AURICAL Aud with HI-PRO 2

Switching off AURICAL Aud

1. To switch off AURICAL Aud, disconnect the power supply from the mains outlet.

Otometrics - AURICAL Aud

5 Unpacking and Installing

Summary of Contents for AURICAL Aud









































































































































Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands

otometrics AURICAL Aud, Reference Manual

Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands