otometrics AURICAL Aud Reference Manual Download Page 129 | Manualshive

Page: 129 / 136

background image

•

AURICAL speaker unit for integration with AURICAL FreeFit

•

Sound field loudspeakers

•

Monitor headphones with boom microphone

•

Desktop microphone

•

Talkback microphone

•

Patient Responder

•

Power supply and mains cable

•

Wall mounting plate

•

Connection cables

•

AURICAL FreeFit

•

AURICAL Aud Reference Manual

•

AURICAL Aud User Guide

13.5

Notes on EMC (Electromagnetic Compatibility)

•

AURICAL Aud is part of a medical electrical system and is thus subject to special safety precautions. For this reason, the
installation and operating instructions provided in this document should be followed closely.

•

Portable and mobile high-frequency communication devices, such as mobile phones, may interfere with the func-
tioning of AURICAL Aud.

Guidance and manufacturer's declaration - electromagnetic emissions for all equipment and systems

AURICAL Aud is intended for use in the electromagnetic environment specified below. The user of AURICAL Aud should ensure that it is used in such an envir-

onment.

Emissions test

Compliance

Electromagnetic environment - guidance

RF emissions

CISPR 11

Group 1

AURICAL Aud uses RF energy only for its internal function. Therefore, its RF emissions are very low and are

not likely to cause any interference in nearby electronic equipment.

RF emissions

CISPR 11

Class B

AURICAL Aud is suitable for use in all environments, including domestic environments and those directly

connected to the public low-voltage power supply network that supplies buildings used for domestic

purposes.

Guidance and manufacturer's declaration - electromagnetic immunity for all equipment and systems

AURICAL Aud is intended for use in the electromagnetic environment specified below. The user of AURICAL Aud should ensure that it is used in such an envir-

onment.

Immunity test

IEC 60601

test level

Compliance

level

Electromagnetic environment - guidance

Electrostatic discharge (ESD)

IEC 61000-4-2

+/- 6 kV con-

tact

+/- 8 kV air

+/- 6 kV con-

tact

+/- 8 kV air

Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material,

the relative humidity should be at least 30 %.

Otometrics - AURICAL Aud

129

13 Technical specifications

«
...
127
128
129
130
131
...
»

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Related manuals for AURICAL Aud

Brand: IFR Pages: 46

Brand: TA Instruments Pages: 7

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 38

Brand: Yamaha Pages: 45

Brand: Gas Data Pages: 99

Brand: Dwyer Instruments Pages: 189

Brand: Lowrey Pages: 109

Brand: GMC-I Prosys Pages: 10

Brand: S&S Northern Pages: 5

Brand: Trotec Pages: 14

Brand: RS PRO Pages: 44

WM14-96 - PROGRAMMING

Brand: CARLO GAVAZZI Pages: 6

Brand: PANCONTROL Pages: 157

Brand: Hanna Instruments Pages: 25

Brand: Hanna Instruments Pages: 2

Brand: Vogel Pages: 4

K-PATENTS PR-23 AX Series

Brand: Vaisala Pages: 246

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands