manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 84

1. In the Speech Audiometry control panel, click the

Calibrate

button to open the

Portable Sound-Field Audiometry

window.

First, configure the speaker setup:

2. Select the output that you want to calibrate- either the built-in AURICAL Aud speaker, or external speakers.

3. Indicate the speaker's position in relation to the client.

4. If you are using two speakers, you can select the

Lock Stimulus to Speaker 1

option to present the stimulus from

speaker 1 and masking from speaker 2.

Calibrate the speaker or speakers:

5. Before you start the calibration, position the sound level meter in the location where the client's head will be.

6. Select the speaker that you want to calibrate.

If you use two speakers, you must calibrate first one and then the other. If you use only one speaker, you only need to
calibrate the left speaker.

7. Click

Start calibration

.

The primary signal is played.

8. Use the Up and Down buttons to adjust the level until the sound level meter reads 70 dB and then click

Accept Level

The primary signal stops and the secondary signal is played.

9. Again, use the arrow buttons to adjust the level until the sound level meter reads 70 dB, and then click

Accept Level

.

10. If you are using two speakers, select the second speaker as the channel to calibrate, and then repeat steps 6-8.

11. Click

OK

to save the calibration values and close the dialog.

4.4.3

Using manual speaker calibration values

After you perform a manual calibration of the AURICAL Aud speakers, you can use the values for the room where the cal-
ibration was performed.

To use the manual calibration values:

1. In the Control panel, select

Portable Sound-Field Audiometry

.

Now you can continue to perform Speech audiometry as you normally would.

84

Otometrics - AURICAL Aud

4 Examples of audiometric testing

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands