manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 111

10

Maintenance and calibration

10.1

Service and repair

It is recommended that you keep the packing material in which AURICAL Aud was delivered. If you need to send it in for
service, the original packing material will ensure protection against damage during transport, etc.

Warning

•

For the sake of safety and in order not to void the warranty, service and repair of electro-medical

equipment should be carried out only by the equipment manufacturer or by service personnel at authorized work-
shops. In case of any defects, make a detailed description of the defect(s) and contact your supplier. Do not use a
defective device.

Note

•

There are no user-serviceable parts inside the AURICAL Aud cabinet.

10.1.1

Fuses

AURICAL Aud has no user-accessible fuses.

AURICAL Aud with HI-PRO 2 has no user-accessible fuses.

10.2

Maintenance

AURICAL Aud requires no preventive maintenance except for regular calibration of the transducers.

See

Calibration

►

112

.

10.3

Cleaning

There are no specific requirements to sterilization or disinfection of the test device.

Cleaning the device

Make sure that the instrument is kept clean and free of dust:

•

Remove dust using a soft brush.

•

To clean the cabinet, use a soft, slightly damp cloth with a small amount of mild detergent on it.

Caution

•

Do not allow any moisture inside the instrument!

Cleaning accessories

Headphones

The headphones are in constant contact with the patient, and should therefore be kept clean.

Clean the headphones between patients, e.g. with a non-alcohol based antibacterial wipe, such as Audiowipes.

Otometrics - AURICAL Aud

111

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands