otometrics AURICAL Aud Reference Manual Download Page 58

Page: 58 / 136

SISI Stimulus Bar

Intensity

Stimulus indicator

Transducer indicator

Routing indicator

Stimulus bar color

Frequency

Intensity

Indicated by the dB level above the channel status bars.
•

The green wave symbol above the level indicates with two waves that the stimulus carrier tone is currently being
presented, and with three waves that the increment is applied.

Stimulus bar color

Indicates the routing for the channel:
•

Blue = left ear

•

Red = right ear

Stimulus, transducer and routing indicators

Indicates the stimulus type, the transducer and the routing for each channel.

Test controls

Test controls provide a means of operating the audiometer if you use the mouse and on-screen options to perform tests.

•

To enable test controls, select

Tools

Options

Audiometry

General

On-screen controls

Controlling intensity and frequency, and storing data

•

The

Arrow up

button increases the intensity.

•

The

Arrow down

button decreases the intensity.

•

The

Arrow left

button decreases the stimulus frequency.

•

The

Arrow right

button increases the stimulus frequency.

Store

•

Stores the data point.

Scoring Level Intensity Change Recognition

•

Click the

button each time the patient acknowledges that a change in

intensity was heard

•

Play

button

Starts the test.

Otometrics - AURICAL Aud

2 Navigating in the OTOsuite Audiometry Module

Summary of Contents for AURICAL Aud









































































































































Search results

Summary of Contents for AURICAL Aud

Reviews:

Brands by name

Popular brands

otometrics AURICAL Aud, Reference Manual

Search results

Summary of Contents for AURICAL Aud

Reviews:

Brands by name

Popular brands