otometrics AURICAL Aud Reference Manual Download Page 103

Page: 103 / 136

Communicating with the device

Connecting to the device

OTOsuite is designed to communicate with and display test data generated by Otometrics test devices.

•

When you start up OTOsuite, click on the

Control Panel

icon. OTOsuite will automatically connect to the test device.

•

See also the section "Activating the Control Panel" in the OTOsuite User Guide.

Firmware update

If a Firmware Update message appears, see:

•

Updating device firmware

►

103

Information about the test device

To see information relating to the test device, select

Help

About Device

7.1

Reconnecting to the device

If the control panel for a test type is shown, and communication with the selected test device is interrupted, a message
appears stating that there is no longer connection to the device.

•

Click the

Connect

button on the

Control Panel

to reconnect to the selected test device.

7.2

Updating device firmware

If the OTOsuite software version contains a more recent firmware for the device, a message will appear when next you
switch on the device.

It is recommended that you update the device firmware to make sure that the device and OTOsuite perform correctly.

•

Follow the on-screen instructions.

Otometrics - AURICAL Aud

103

Summary of Contents for AURICAL Aud









































































































































Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands

otometrics AURICAL Aud, Reference Manual

Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands