otometrics AURICAL Aud Reference Manual Download Page 26

Page: 26 / 136

Up and down arrows

Tone and Speech. Stimulus and Masking

•

The Arrow Up and the Arrow Down buttons change the stimulus level depending on the set-
ting in

Tools

Options

Audiometry

Tone

Misc.

Level Direction of Arrow Keys

Left and right arrows

Tone. Stimulus and Masking

•

Arrow left decreases the stimulus frequency.

•

Arrow right increases the stimulus frequency.

Stimulate button

Present

Tone

•

Presents stimulus.

•

Continuous On

is enabled, activating the button interrupts the stimulus.

Store button

Store

Tone and Speech

•

Stores the data point on the audiogram(s) or in the Speech screen.

Silence Mode

Silence Mode allows you to control tone levels and presentation by hovering the mouse cursor over the respective on-
screen controls. This is particularly useful when the operator of the audiometer and the person being tested are in the
same room.

•

To enable silence mode, select

Tools

Options

Audiometry

General

On-screen controls

Silence Mode

•

To change the level and frequency by more than one click at a time, use the mouse scroll wheel.

2.6.2

The Tone stimulus bar

Symbol

Frequency

During online testing, the stimulus bar shows:

Otometrics - AURICAL Aud

2 Navigating in the OTOsuite Audiometry Module

Summary of Contents for AURICAL Aud









































































































































Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands

otometrics AURICAL Aud, Reference Manual

Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands