manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 90

4. Follow the on-screen instructions.

Powered USB connections for accessories

Caution

•

Install the OTOsuite Audiometry Module on the PC before you connect AURICAL Aud to the PC.

These USB connections are powered up to 500 mA, so that, for instance, you can connect the USB double-cable version of
OTOcam to two of these USB connections.

To connect accessories to AURICAL Aud, use the supplied USB cable(s).

1. Plug one end of the USB cable(s) into the USB socket in the connection panel and the other end into a USB socket on

the accessory.

External power supply

Warning

•

Use only the power supply provided by Otometrics.

Warning

•

AURICAL Aud is not provided with a mains switch.

To connect AURICAL Aud to the mains supply, plug the mains plug into the wall mains outlet.
To disconnect AURICAL Aud from the mains supply, pull the mains plug out of the wall mains outlet. Do not pos-
ition the unit so that it is difficult to pull the mains plug out of the wall mains.

See

Power supply

►

127

for details.

1. Plug the external power supply into the Power socket in the connection panel.

2. Plug the mains plug of the external power supply into an AC mains outlet with a three-wire protective ground.

Sound field speaker output (optical digital line-out)

Optical connection for connecting to an external amplifier for sound field speaker(s). (Currently not in use.)

Sound field speaker output (coaxial digital line-out)

Coaxial connection for connecting to an external amplifier for sound field speaker(s). (Currently not in use.)

Sound field speakers (built-in amplifier output)

Connections for the AURICAL speaker unit and the PMM sound field speakers using the built-in amplifiers (2 sound field
speakers are supported in the software).

•

Plug the AURICAL speaker unit into socket no. 3.

•

If you are using two sound field speakers in addition to or instead of the AURICAL speaker, plug the cable of the left
speaker into socket no. 1, and the cable of the right speaker into socket no. 2.

•

If you are using two sound field speakers in addition to or instead of the AURICAL speaker, set up the configuration in
the Configuration Wizard in OTOsuite. See

Configuring the Audiometry Module

►

101

.

90

Otometrics - AURICAL Aud

5 Unpacking and Installing

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands