otometrics AURICAL Aud Reference Manual Download Page 115 | Manualshive

Page: 115 / 136

background image

12

Standards and Safety

This manual contains information and warnings, which must be followed to ensure the safe performance of the devices and
software covered by this manual. Local government rules and regulations, if applicable, should also be followed at all times.

Standards and safety-related issues relating to HI-PRO 2 are comprised by the AURICAL Aud symbols, standards and warning
notes.

See

and

12.1

AURICAL Aud

Electronic equipment covered by the Directive 2002/96/EC on waste electrical and electronic equipment
(WEEE).

All electrical and electronic products, batteries, and accumulators must be taken to separate collection at
the end of their working life. This requirement applies in the European Union. Do not dispose of these
products as unsorted municipal waste.

You can return your device and accessories to Otometrics, or to any Otometrics supplier. You can also con-
tact your local authorities for advice on disposal.

Consult user manual for warnings and cautions.

Consult instructions for use.

Without HI-PRO 2

Complies with Type B requirements of IEC60601-1.

With HI-PRO 2

Complies with Type B requirements of IEC60601-1.

Complies with Type BF requirements of IEC60601-1.

Complies with Medical Devices Directive 93/42/EEC and RoHS Directive (2011/65/EC).

MEDICAL - General Medical Equipment as to electrical shock, fire and mechanical hazards only in accord-
ance with UL 60601-1, first edition, 2003 CAN/CSA-22.2 No. 601.1-M90.

Suitable for direct current only.

12.2

Warning notes

12.2.1

Connector warning notes

Warning

•

Never mix connections between the two types of connectors shown below:

Otometrics - AURICAL Aud

115

«
...
113
114
115
116
117
...
»

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Related manuals for AURICAL Aud

Brand: TANDBERG Pages: 53

CP-4900 Micro-GC

Brand: Varian Pages: 7

Brand: Vapotherm Pages: 2

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 110

Portatone PSR-5700

Brand: Yamaha Pages: 79

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 108

PLUS 3631 Series

Brand: insize Pages: 1

Brand: Datakom Pages: 28

Brand: Solartron Mobrey Pages: 34

Digital Piano CA440

Brand: Kawai Pages: 48

Brand: JUMO Pages: 150

Brand: Parkside Pages: 199

Commissioner dali

Brand: Artistic License Pages: 26

Brand: Novus Pages: 52

Brand: Rockler Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands