otometrics AURICAL Aud Reference Manual Download Page 93

Page: 93 / 136

It is a general rule for all electrical equipment used in the proximity of the client that:

•

The connected equipment must comply with IEC 60601-1 and/or IEC 60601-1-1

except for the PC, and equipment connected to the line in and the line out sockets of AURICAL Aud.

•

To access the AURICAL speaker unit connection panel, remove the speaker cover.

USB

•

USB socket for connecting the speaker to the no. 3 USB socket on the
AURICAL Aud connection panel.

See

AURICAL speaker unit installation

►

BT (Bluetooth)

•

Socket for Bluetooth dongle.

Insert the Bluetooth dongle in this socket for communication between
AURICAL FreeFit and the OTOsuite PMM module.

For a description of Bluetooth communication between PMM and
AURICAL FreeFit, see the AURICAL FreeFit User Manual.

Power supply connections

Caution

•

Install the OTOsuite Audiometry Module on the PC before you connect AURICAL Aud to the PC.

24V dc out

•

Double-ended male connector for connecting the power supply to AURICAL
Aud.

See

AURICAL speaker unit installation

►

24V dc in

•

Power supply connector for the external power supply of the AURICAL
speaker unit.

Speaker connection

Speaker input

•

Sound field speaker connection to the AURICAL speaker unit from AURICAL
Aud.

See

AURICAL speaker unit installation

►

5.6

Assembling AURICAL Aud

Caution

•

Install the OTOsuite Audiometry Module on the PC before you connect AURICAL Aud to the PC.

Otometrics - AURICAL Aud

5 Unpacking and Installing

Summary of Contents for AURICAL Aud









































































































































Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands

otometrics AURICAL Aud, Reference Manual

Search results

Summary of Contents for AURICAL Aud

Reviews:

Related manuals for AURICAL Aud

Brands by name

Popular brands