manualshive.com logo in svg

Omron NT-SERIES - SUPPORT TOOL FOR WINDOWS V4, Operation Manual

The Omron NT-SERIES Support Tool for Windows V4 is a comprehensive software that allows users to easily manage and configure their Omron NT-series HMI devices. This tool is essential for programming and monitoring these devices efficiently. Download the free Operation Manual from manualshive.com to get started.

Share
Download
background image

6-2

Section

Fixed Display

143

Circles can be used with all models except for NT11S/NT11.

(1) A circle is drawn. The radius of a circle can be changed.

Operation procedure

Selection using the menu bar:

[Objects] 

→

 [Fixed Display] 

→

 [Circle]

Selection using the drawing toolbar:

Terminology

Center point

Property setting

General

Position

Center point:

Indicates the position of the center of a circle.

Size:

Indicates the radius of a circle.

Attribute:

Specify the display attribute. (Setting is not possible with NT20,

NT20S and NT600S) Standard, Inverse, Flash, Inverse Flash

Color

Foreground:

Specify the line color.
(Can only be set for PTs with color display.)
White, black, blue, red, magenta, green, cyan, yellow

Guidance

A circle element can be modified in the manner shown below.

A circle can be modified by dragging a green 

 mark (handle).

Summary of Contents for NT-SERIES - SUPPORT TOOL FOR WINDOWS V4



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NT-SERIES - SUPPORT TOOL FOR WINDOWS V4

KAPERSKY ANTI-VIRUS 5.0 - FOR SAMBA SERVERS Administrator'S Manual preview
ANTI-VIRUS 5.0 - FOR SAMBA SERVERS
Brand: KAPERSKY Pages: 84
KAPERSKY ADMINISTRATION KIT 6.0 Getting Started preview
ADMINISTRATION KIT 6.0
Brand: KAPERSKY Pages: 37
KAPERSKY ADMINISTRATION KIT 6.0 Deployment Manual preview
ADMINISTRATION KIT 6.0
Brand: KAPERSKY Pages: 109
Xerox WORKCENTRE C2424 Manual preview
WORKCENTRE C2424
Brand: Xerox Pages: 12
Xerox WorkCentre M118 Getting Started Manual preview
WorkCentre M118
Brand: Xerox Pages: 25
Autodesk AUTODESK ROBOT STRUCTURAL ANALYSIS PROFESSIONAL Brochure preview
AUTODESK ROBOT STRUCTURAL ANALYSIS PROFESSIONAL
Brand: Autodesk Pages: 6
Cabletron Systems SmartCell ZX Administrator Installation Manual preview
SmartCell ZX Administrator
Brand: Cabletron Systems Pages: 34
Brady markware User Manual preview
markware
Brand: Brady Pages: 33
Kenwood MediaManager Installation Manual preview
MediaManager
Brand: Kenwood Pages: 40
Altigen Call Detail Reporting Manual preview
Call Detail Reporting
Brand: Altigen Pages: 97
Altigen Altiware OE 4.5 System Administration & Installation Manual preview
Altiware OE 4.5
Brand: Altigen Pages: 455
Amanda Amanda@Work.Group/DOS Version 7.xx User Manual preview
[email protected]/DOS Version 7.xx
Brand: Amanda Pages: 84
Amanda Amanda Portal CallQ Agent User Manual preview
Amanda Portal CallQ Agent
Brand: Amanda Pages: 61
Amanda Amanda Portal Telephone Features System Reference Manual preview
Amanda Portal Telephone Features
Brand: Amanda Pages: 226
Intel Active Management Technology v5.0 Administrator'S Manual preview
Active Management Technology v5.0
Brand: Intel Pages: 143
UNIBLUE SpeedUpMyPC 2010 Product Manual preview
SpeedUpMyPC 2010
Brand: UNIBLUE Pages: 11
Autodesk 507B1-90A211-1301 - NavisWorks Manage 2010 User Manual preview
507B1-90A211-1301 - NavisWorks Manage 2010
Brand: Autodesk Pages: 472
IBC BoilerNet Interface Controller II User Manual preview
BoilerNet Interface Controller II
Brand: IBC Pages: 52

Brands by name

Popular brands

Load more brands