manualshive.com logo in svg

Omron NT-SERIES - SUPPORT TOOL FOR WINDOWS V4, Operation Manual

Share
Download
Omron NT-SERIES - SUPPORT TOOL FOR WINDOWS V4 Operation Manual Download Page 293

7-2

Section

Numeral Memory Table

277

(6) Click on 

 to close the dialog box.

(7) Click on the table entry number of the copy source table.

(8) Click on 

 or right click the table entry number.

(9) Select [Copy to Next].

7-1-6 Table Display Operation by Specifying the Table Entry Number

Description of [Go to] dialog box

Entry

Specify the table entry number of the table to be displayed.

The cursor moves to the specified table entry number.

Operation procedure

(1) Click on 

.

(2) Specify the table entry number of the table to be displayed.

(3) Click on 

.

7-2

Numeral Memory Table

Numeral Memory Table

The numeral memory table is an area provided in a PT to store numeric value
data.

A numeral memory table entry is allocated to one or two words in a PC (PLC) and
the numeral memory table entry used for display can be shared with the PC
(PLC).

Summary of Contents for NT-SERIES - SUPPORT TOOL FOR WINDOWS V4



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands