MerCruiser 496 MAG Bravo User Manual Download Page 81

Page: 81 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 73

4. Place the oil drain hose in a suitable container.
5. Remove the drain plug from the oil drain hose.
6. After oil has drained completely, install the drain plug in the oil drain hose.
7. Push the hose through bilge drain and install the plug.

ENGINE OIL DRAIN PUMP

1. Loosen the oil filter to vent the system.
2. Remove the dipstick.
3. Install the oil pump onto the dipstick tube.

mc70571-1

a -

Typical oil pump

b -

Dipstick tube

c -

Oil drain hose

4. Insert the hose end of the crankcase oil pump onto an appropriate container and, using

the handle, pump until the crankcase is empty.

5. Remove the pump.
6. Install the dipstick.

CHANGING FILTER

1. Remove and discard oil filter.

8483

a -

Oil filter

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands