MerCruiser 496 MAG Bravo User Manual Download Page 121

Page: 121 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 113

2. Close the seacock, if equipped.

18510

For visual clarity, the secock shown is not installed

a -

Hose fitting to engine

b -

Seacock

c -

Handle (closed position)

d -

To water source pickup attachment

3. If equipped with an alternative water pickup and not equipped with a seacock,

disconnect the water hose from the alternative water pickup and plug both ends,

excluding the Bravo sterndrive.

4. Ensure that the inlet water hose from the sterndrive to the engine is connected.
5. Remove the quick‑connect fitting from the parts bag supplied with the engine.
6. Attach the quick‑connect fitting to a water hose.

18487

a -

Quick connect fitting (water hose

end)

b -

Water hose

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands