MerCruiser 496 MAG Bravo User Manual Download Page 106

Page: 106 / 146

Section 5 - Maintenance

Page 98

90-864839061 NOVEMBER 2006

5. Bend the 3 tabs down into the grooves.

4750

a -

Prop

b -

Tab washer

c -

Drive sleeve adapter

d -

Tab bent down

e -

Propeller nut

BRAVO TWO MODELS

IMPORTANT: Use the correct rotation propeller. The propeller rotation MUST match the

direction of rotation of the propeller shaft.
1. Liberally coat the propeller shaft spline with one of the following Quicksilver lubricants.

Tube Ref No.

Description

Where Used

Part No.

Special Lubricant 101

Propeller shaft splines

92-802865A1

2-4-C Marine Lubricant with

Teflon

Propeller shaft splines

92-802859A1

Anti-Corrosion Grease

Propeller shaft splines

92-802867A1

NOTE: Anti‑corrosion grease is for salt water applications only.

2. Install the propeller with the attaching hardware as shown.
3. Torque the propeller nut.

8566

Bravo Two

a -

Propeller shaft splines

b -

Forward thrust hub

c -

Propeller

d -

Spline washer

e -

Tab washer

f -

Propeller nut

NOTE: The propeller torque stated is a minimum torque value.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands