MerCruiser 496 MAG Bravo User Manual Download Page 119 | Manualshive

Page: 119 / 146

background image

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 111

ALTERNATIVE WATER PICKUPS

IMPORTANT: Two water sources are needed for this procedure.

NOTE: Flushing is needed only for salty, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

IMPORTANT: Engines with the sterndrive water inlet blocked off at the gimbal housing and

using a through‑hull water inlet need a supply of cooling water available to both the

sterndrive and to the engine during operation.
1. If flushing the cooling system with the boat in the water:

a.

Raise sterndrive to trailer position.

b.

Install the appropriate flushing attachment over the water inlet holes in the gear

housing.

c.

Lower sterndrive to full down (in) position.

2. If flushing the cooling system with the boat out of the water:

a.

Lower sterndrive to full down (in) position.

!

WARNING

Contact with moving drive components and the propeller can cause personal injury or

death. To avoid possible injury, remove the propeller and ensure that no people or

animals are in the area of the drive unit while flushing.

b.

Remove propeller.

c.

Install the appropriate flushing attachment over the water inlet holes in the gear

housing.

3. Connect hose between flushing attachment and water source.
4. Close the seacock, if equipped, to prevent water from siphoning into the engine or boat.
5. Remove the seawater inlet hose from the seawater pump and plug the hose to prevent

water from siphoning into the engine or boat.

6147

6. Using a suitable adapter, connect the flushing hose from the water source to the water

inlet of the seawater pump.

!

CAUTION

Overheating from insufficient cooling water will cause engine and drive system damage.

Ensure that there is sufficient water always available at water inlet holes during operation.

7. With sterndrive in normal operating position, open the water source fully.
8. Place the remote control in neutral idle speed position and start engine.

«
...
117
118
119
120
121
...
»

Summary of Contents for 496 MAG Bravo



















































































































































Reviews:

No comments

Related manuals for 496 MAG Bravo

Brand: Ibiza Pages: 3

Brand: Aerotech Pages: 59

Command Pro CH940-CH1000

Brand: Kohler Pages: 16

Brand: hager Pages: 4

Calzoni MR Series

Brand: Parker Pages: 50

Brand: Honda Pages: 139

Brand: Honda Pages: 64

Brand: Honda Pages: 84

Brand: Volvo Penta Pages: 84

Brand: Volvo Penta Pages: 88

Brand: Volvo Penta Pages: 41

240Z S30 series

Brand: Datsun Pages: 41

Brand: NSK Pages: 33

Brand: Robin America Pages: 88

Brand: Yanmar Pages: 168

ZA top SM225.40B

Brand: ZIEHL-ABEGG Pages: 76

Brand: Mitsubishi Pages: 61

Brand: Honda Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands