MerCruiser 496 MAG Bravo User Manual Download Page 141

Page: 141 / 146

Section 7 - Troubleshooting

90-864839061 NOVEMBER 2006

Page 133

Power Trim Does Not Operate (Motor Does Not Operate)

Possible Cause

Remedy

Blown fuse.

Replace fuse. Fuses may be located near the dash

trim switch, at the trim pump, in the positive (red)

power trim battery lead near the battery switch, or a

combination of these.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires

(especially battery cables). Clean and tighten faulty

connection. Repair or replace wiring.

Power Trim Does Not Operate (Motor Operates But Sterndrive Unit

Does Not Move)

Possible Cause

Remedy

Trim pump oil level low.

Fill pump with oil.

Drive unit binding in gimbal ring.

Check for obstruction.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands