MerCruiser 496 MAG Bravo User Manual Download Page 35

Page: 35 / 146

Section 2 - Getting to Know Your Power Package

90-864839061 NOVEMBER 2006

Page 27

CONSOLE MOUNT FEATURES

mc79503-1

a -

Throttle Only Button

b -

Control Handle

c -

Power Trim Switch

d -

Trailer Switch

Throttle Only Button -

Allows engine throttle advancement without shifting the engine.

This is done by disengaging the shift mechanism from the control handle. The throttle only

button can be depressed only when the remote control handle is in the neutral position.

Control Handles -

Operation of the the shift and throttle are controlled by the movement

of the control handle. Push the control handle forward from neutral with a quick firm motion

to the first detent for forward gear and continue pushing forward to increase speed. Pull

the control handle back from neutral with a quick firm motion to the first detent for reverse

gear and continue pushing back to increase speed.

Control Handle Tension Adjustment Screw - (not visible)

This screw is used to adjust

the effort required to move the remote control handle. Refer to instructions provided with

remote control for complete adjustment instructions.

Power Trim Switch -

See

Power Trim

section for detailed power trim operating

procedures.

Trailer Switch -

Used to raise drive unit for trailering, launching, beaching or shallow water

operation. See

Power Trim

for detailed trailer switch operation.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands