MerCruiser 496 MAG Bravo User Manual Download Page 70

Page: 70 / 146

Section 4 - Specifications

Page 62

90-864839061 NOVEMBER 2006

Models

496 MAG

496 MAG HO

Horsepower

375

425

Kilowatts

280

317

Number of cylinders

Displacement

8.1 L (496 cid)

Bore and Stroke

108 × 111 mm (4.25 × 4.38 in.)

Compression ratio

9.1:1

Idle RPM in neutral

650

Specified WOT RPM range

4400‑4800

4600‑5000

Minimum oil pressure @ idle

103 kPa (15 psi)

Thermostat

71° C (160° F)

Timing @ idle

Not Adjustable

Firing order

1‑8‑7‑2‑6‑5‑4‑3

Electrical system

12‑Volt Negative (‑) Ground

Alternator Rating

65 amp

Recommended battery rating (Non‑DTS models) (minimum)

750 CCA, 950 MCA, or 180 Ah

Recommended battery rating (DTS models) (minimum)

800 CCA, 1000 MCA, or 190 Ah

Spark plug type

AC Platinum (AC 41‑983)

Spark plug gap

1.5 mm (0.060 in.)

Fluid Specifications (496)

Fluid Specifications

IMPORTANT: All capacities are approximate fluid measures.

Engine

IMPORTANT: It may be necessary to adjust oil levels depending on installation angle and

cooling systems (heat exchanger and fluid lines).
Always use the dipstick to determine the exact quantity of oil or fluid required.

All Models

Capacity

Fluid Type

Engine oil (with filter)

8.5 liters (9 U.S. qt.) Mercury/Quicksilver Synthetic Blend

MerCruiser Engine Oil 25W‑40

Seawater cooling system (winterization use

only)

20 liters (21 U.S. qt.) Propylene Glycol and Purified Water

Closed cooling system

18 liters (19 U.S. qt.)

Mercury Extended Life Coolant/

Antifreeze or Extended Life Ethylene

Glycol 5/100 Coolant/Antifreeze mixed

50/50 with Purified Water

Bravo Sterndrives

NOTE: Oil capacity includes gear lube monitor.

Model

Capacity

Fluid Type

Bravo One

2736 ml (92‑1/2 oz.)

High Performance Gear Lubricant

Bravo Two

3209 ml (108‑1/2 oz.)

Bravo Three

2972 ml (100‑1/2 oz.)

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands