MerCruiser 496 MAG Bravo User Manual Download Page 24 | Manualshive

Page: 24 / 146

background image

Section 1 - Warranty

Page 16

90-864839061 NOVEMBER 2006

"DISP" ‑ Piston Displacement

OMXXXXXX

Dec 2004

X.XL

SERIAL#

D.O.M.

DISP.

FAMILY

FEL.

XXXXX XXXXXX

XX.X g/kW-hr

EMISSION CONTROL
INFORMATION

THIS ENGINE CONFORMS TO 2003 CALIFORNIA EMISSION
REGULATIONS FOR SPARK IGNITION MARINE ENGINES

REFER TO OWNER'S MANUAL FOR MAINTENANCE
SPECIFICATIONS AND ADJUSTMENTS

0575

10652

Emission Control Label ‑ CE Marked

"SERIAL#" ‑ Engine Serial Number
"FAMILY" ‑ Engine Family
"FEL." ‑ Family Emission Limit
"D.O.M." ‑ Date of Manufacture
"DISP" ‑ Piston Displacement
CE ‑ When this mark is present in the lower right corner of the Emission Control Information

Label, on the engine, the Declaration of Conformance applies. Refer to the front page of

this Manual for further information.

Owner Responsibility

The owner/operator is required to have routine engine maintenance performed to maintain

emission levels within prescribed certification standards.
The owner/operator is not to modify the engine in any manner that would alter the

horsepower or allow emissions levels to exceed their predetermined factory specifications.

Emission Certification Star Label

Your boat is labeled on the hull with one of the following star labels. The Symbol for Cleaner

Marine Engines Means:
1. Cleaner Air and Water ‑ for a healthier lifestyle and environment.
2. Better Fuel Economy ‑ burns up to 30‑40 percent less gas and oil than conventional

carbureted two‑stroke engines, saving money and resources.

3. Longer Emission Warranty ‑ Protects consumer for worry free operation.
Beginning January 1, 2003, one Three‑Star label will be included with each factory‑certified

Mercury MerCruiser engine.
All Mercury MerCruiser engines (500 hp and below) will have a Three‑Star Ultra Low

Emission rating. The Three‑Star label identifies that these engines meet the California Air

Resources Board's Sterndrive and Inboard marine engine 2003 exhaust emission

standards. Engines meeting these standards have 65% lower emissions than One‑Star ‑

Low Emissions engines.

«
...
22
23
24
25
26
...
»

Summary of Contents for 496 MAG Bravo



















































































































































Reviews:

No comments

Related manuals for 496 MAG Bravo

Brand: Hyster Pages: 25

Brand: GRITAL Pages: 4

Brand: Mercedes-Benz Pages: 940

IE3-K11R 132S 4 Ex e IIC T3

Brand: VEM Pages: 16

Brand: Baratza Pages: 5

Brand: Scania Pages: 78

Brand: LAMBERT Pages: 24

Brand: EBARA Pages: 36

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 13

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands