MerCruiser 496 MAG Bravo User Manual Download Page 47

Page: 47 / 146

Section 2 - Getting to Know Your Power Package

90-864839061 NOVEMBER 2006

Page 39

6. The power trim system is protected from overload by a 110 amp fuse and a 20 amp

spade fuse on the power trim pump. The trim pump may also have an in‑line circuit

protection device in the power trim positive lead near the battery switch or battery

connection.

9208

a -

20 amp spade fuse

b -

110 amp fuse

7. The Quicksilver Three‑Button Power Trim Control Panel is further protected by a 20

amp in‑line fuse.

mc70527-1

8. The Quicksilver MerCathode System has a 20 amp in‑line fuse in the wire which

connects to the positive (+) terminal on controller. If the fuse is blown, the system will

not operate resulting in a loss of corrosion protection.

mc79977

Audio Warning System

Your Mercury MerCruiser power package may be equipped with an Audio Warning System.

The Audio Warning System will not protect the engine from damage. It is designed to warn

the operator that a problem has occurred.
The audio warning system will sound with a continuous horn if one of the following occurs:

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands