MerCruiser 496 MAG Bravo User Manual Download Page 122 | Manualshive

Page: 122 / 146

background image

Section 5 - Maintenance

Page 114

90-864839061 NOVEMBER 2006

7. Snap the quick‑connect fitting with the water hose into the flush socket on the engine.

a

b

c

18489

a -

Water hose

b -

Quick‑connect fitting (water hose

end)

c -

Flush socket

8. Open the water source of the water hose to a full flow.
9. Allow the water to flush the sterndrive for 30 seconds.
10. Place the remote control in neutral idle speed position and start engine.

!

CAUTION

Overheating from insufficient cooling water will cause engine and drive system damage.

Ensure that there is sufficient water always available at water inlet holes during operation.

11. Operate the engine at idle speed in neutral gear. Do not exceed 1200 RPM.
12. Monitor the engine temperature while operating the engine.
13. Flush the engine for 5 to 10 minutes or until discharge water is clear.
14. Shut off the engine.
15. Allow the water to flush the sterndrive for 10 seconds.
16. Turn off the water source.

«
...
120
121
122
123
124
...
»

Summary of Contents for 496 MAG Bravo



















































































































































Reviews:

No comments

Related manuals for 496 MAG Bravo

Brand: Mack Pages: 303

Brand: Yanmar Pages: 224

950-1020 MOTOR KIT 8504048 REV 2 1297

Brand: TJERNLUND Pages: 2

Brand: Graco Pages: 26

Brand: Deutz Pages: 37

Brand: Yamaha Pages: 30

NIIGATA MG(L)26HLX

Brand: IHI Pages: 204

Brand: GE Pages: 10

Brand: GE Pages: 20

310000 - REVISION C

Brand: GE Pages: 24

Brand: MINN KOTA Pages: 42

Brand: Toyama Pages: 44

Brand: Reely Pages: 4

Brand: Crestron Pages: 2

Brand: Hacker Pages: 8

Brand: Hacker Pages: 8

Brand: Hacker Pages: 38

Brand: DANA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands