MerCruiser 496 MAG Bravo User Manual Download Page 46

Page: 46 / 146

Section 2 - Getting to Know Your Power Package

Page 38

90-864839061 NOVEMBER 2006

2. A 90 amp fuse is located on the large post of the starter solenoid. This fuse is designed

to protect the engine wiring harness if an electrical overload occurs.

mc74907-1

3. Four fuses are located on the port side of the engine. These fuses protect various

Electronic Fuel Injection (EFI) circuits.

mc77602-1

4. The main power and fuel pump relays are located next to the fuses and control voltage

to the engine with the ignition key in the "ON" position.

mc77602-2

5. A 20 amp fuse may be located in the ignition switch "I" terminal lead to protect the

electrical system. Check for blown fuse if the ignition key is turned to the "START"

position and nothing happens (and circuit breaker is not tripped).

mc70525-1

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands