MerCruiser 496 MAG Bravo User Manual Download Page 107

Page: 107 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 99

Description

lb. in.

lb. ft.

Bravo Two propeller nut

Then align tabs with groves

4. Continue to tighten the propeller nut until the 3 tabs on the tab washer align with the

grooves on the spline washer.

5. Bend the 3 tabs down into the grooves.

4750

a -

Prop

b -

Tab washer

c -

Drive sleeve adapter

d -

Tab bent down

e -

Propeller nut

BRAVO THREE

1. Liberally coat the propeller shaft spline with one of the following Quicksilver lubricants.

Tube Ref No.

Description

Where Used

Part No.

Special Lubricant 101

Propeller shaft splines

92-802865A1

2-4-C Marine Lubricant with

Teflon

Propeller shaft splines

92-802859A1

2-4-C Marine Lubricant with

Teflon

Propeller shaft splines

92-802859A1

NOTE: Anti‑corrosion grease is for salt water applications only.

2. Slide forward thrust hub onto propeller shaft, with tapered side toward propeller hub.
3. Align splines and place front propeller on propeller shaft.
4. Install front propeller locknut and torque using the Propeller Nut Tool.

Propeller Nut Tool

91‑805457T 1

10677

Aids in the removal and installation of the front propeller nut.

Description

lb. in.

lb. ft.

Bravo Three front propeller nut

136

100

5. Slide aft thrust hub onto propeller shaft with tapered side toward propeller hub

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands