MerCruiser 496 MAG Bravo User Manual Download Page 19

Page: 19 / 146

Section 1 - Warranty

90-864839061 NOVEMBER 2006

Page 11

Mercury MerCruiser products installed by a Mercury Installation Quality Certified

Manufacturer are Installation Quality certified products and may receive an additional one

(1) year of limited warranty coverage.
The Installation Quality Certification program was developed to recognize MerCruiser

boatbuilder customers who have achieved higher manufacturing standards. It is the first

and only comprehensive manufacturer‑installation certification program in the industry.
The program has three goals:
1. To enhance overall product quality.
2. To improve the boat ownership experience.
3. To enhance overall customer satisfaction.
The certification process is designed to review all facets of manufacturing and engine

installation. The program is composed of design, manufacturing and installation review

stages with which builders must comply. Certification applies leading‑edge methodologies

to create:
• Efficiencies and best practices specific to engine installation.
• World‑class assembly and component specifications.
• Efficient installation processes.
• Industry standard end‑of‑line test procedures
Boat builders that successfully complete the program and meet all certification

requirements earn Installation Quality System Certified Manufacturer status and receive

an additional one (1) year of Mercury limited factory warranty coverage on all

MerCruiser‑powered boats that are registered on and after the boat builder's certification

date for all worldwide registrations.
Mercury has designated a section of our Website to promote the Installation Quality

Certification Program and communicate its benefits to consumers. For a current list of

MerCruiser‑powered boat brands that have earned Installation Quality Certification, visit

www.mercurymarine.com/mercruiser_warranty.

California Emissions Limited Warranty

NOTE: Mercury Marine does not establish model years for the Mercury MerCruiser product

line. In order to comply with CARB warranty regulations, and for that limited purpose only,

model year shall have the same meaning as calendar year. As an example, 2003 model

year products refers to products manufactured during calendar year 2003.

The California Air Resources Board has promulgated air emissions regulations for inboard

and sterndrive engines. The regulations apply to all inboard and sterndrive engines that

were manufactured for the 2003 model year and later. Mercury Marine, in compliance with

those regulations, provides this limited warranty for the emission control systems (see the

components of the emission control system listed following), and further warrants that the

inboard or sterndrive engine was designed, built, and equipped to conform with all

applicable regulations adopted by the California Air Resources Board pursuant to its

authority in Chapters 1 and 2, Part 5, Division 26 of the Health and Safety Code. For

information regarding the limited warranty for the non‑emissions related components of the

inboard or sterndrive engine, please see the limited warranty statement for your engine.

What Is Covered

NOTE: Mercury Marine does not establish model years for the Mercury MerCruiser product

line. In order to comply with CARB warranty regulations, and for that limited purpose only,

model year shall have the same meaning as calendar year. As an example, 2003 model

year products refers to products manufactured during calendar year 2003.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands