MerCruiser 496 MAG Bravo User Manual Download Page 114

Page: 114 / 146

Section 5 - Maintenance

Page 106

90-864839061 NOVEMBER 2006

IMPORTANT: If anti‑fouling protection is required for the boat hull or boat transom, you

can use copper‑based paint if it is not prohibited by law. If you are using copper based

anti‑fouling paint, observe the following precaution:
• Avoid an electrical interconnection between the Mercury MerCruiser Product, Anodic

Blocks, or MerCathode System and the paint by allowing a minimum of

40 mm (1‑1/2 in.) UNPAINTED area on transom of the boat around these items.

8107

a -

Painted boat transom

b -

Minimum 40 mm (1‑1/2 in.)

unpainted area around transom

assembly

NOTE: Sterndrive and transom assembly can be painted with a good marine paint or an

anti‑fouling paint that DOES NOT contain copper or any other material that could conduct

electrical current. Do not paint drain holes, anodes, the MerCathode system or items

specified by the boat manufacturer.

CAUTION

Improper boat‑cleaning procedures can cause product damage. Washing the

MerCathode assembly, especially with a brush or high‑pressure washer, will damage the

MerCathode assembly making it unable to inhibit galvanic corrosion. When cleaning the

boat, do not use a brush or a high‑pressure washer to wash the MerCathode assembly

found on the bottom of the transom assembly.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands