MerCruiser 496 MAG Bravo User Manual Download Page 69 | Manualshive

Page: 69 / 146

background image

Section 4 - Specifications

90-864839061 NOVEMBER 2006

Page 61

IMPORTANT: When operating a Mercury MerCruiser engine on gasoline containing

alcohol, storage of gasoline in the fuel tank for long periods should be avoided. Long

periods of storage, common to boats, create unique problems. In cars alcohol‑blend fuels

normally are consumed before they can absorb enough moisture to cause trouble, but

boats often sit idle long enough for phase separation to take place. In addition, internal

corrosion may take place during storage if alcohol has washed protective oil films from

internal components.

Engine Oil

To help obtain optimum engine performance and to provide maximum protection, we

strongly recommend the use of the following oils listed in the order of recommendation:
1. MerCruiser / Quicksilver Synthetic Blend, NMMA FC‑W rated, 4 cycle oil.
2. MerCruiser / Quicksilver 25W40 NMMA FC‑W rated oil.
3. A NMMA FC‑W rated oil.
4. MerCruiser / Quicksilver 4‑cycle 25W40, non FC‑W rated oil.
5. A good grade straight weight detergent automotive oil per the operating chart below.

NOTE: The use of non‑detergent oils, multi‑viscosity oils (other than as specified), non

FC‑W rated synthetic oils, low quality oils or oils that contain solid additives are specifically

not recommended.

MerCruiser/ Quicksilver Synthetic Blend, NMMA FC-W rated, 4-cycle oil

MerCruiser / Quicksilver 25W40 NMMA FC-W rated oil

A NMMA FC-W rated oil

MerCruiser / Quicksilver 4-cycle 25W40, non FC-W rated oil

SAE 20W

SAE30W

SAE40W

AIR TEMPERATURE

ORDER OF PREFERENCE

32° F
0° C

50° F
10° C

8082

Engine Specifications (496)

Engine Specifications

NOTE: Performance ratings are obtained and corrected in accordance with SAE J1228/

ISO 8665 Crankshaft Power.
NOTE: All measurements are taken with the engine at normal operating temperature.

«
...
67
68
69
70
71
...
»

Summary of Contents for 496 MAG Bravo



















































































































































Reviews:

No comments

Related manuals for 496 MAG Bravo

HOME MOTION Roll Up 28 WT

Brand: SOMFY Pages: 10

Brand: Avco Lycoming Pages: 106

Brand: Doosan Pages: 108

Brand: LCT Pages: 25

Brand: Cobra Garden Machinery Pages: 64

Brand: Robin America Pages: 36

Brand: Jabiru Pages: 56

Brand: Jonsered Pages: 156

Brand: panthera Pages: 12

Brand: NACIONAL MOTOR Pages: 72

Brand: DLE Pages: 4

Brand: Briggs & Stratton Pages: 112

Brand: Briggs & Stratton Pages: 16

Brand: Gaspar Pages: 27

Brand: Wood-mizer Pages: 192

Brand: Sonny's Pages: 15

ZA top SM160.30B/S

Brand: ZIEHL-ABEGG Pages: 72

Brand: SABB MOTOR Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands