MerCruiser 496 MAG Bravo User Manual Download Page 82

Page: 82 / 146

Section 5 - Maintenance

Page 74

90-864839061 NOVEMBER 2006

2. Coat sealing ring on new filter with engine oil and install.
3. Tighten oil filter securely (following filter manufacturer's instructions). Do not

overtighten.

4. Remove oil fill cap.
IMPORTANT: Always use dipstick to determine exactly how much oil is required.
5. Add recommended engine oil to bring level up to the bottom of the OK range on the

dipstick.

6. With the boat at rest in the water, check the oil level and add specified fluid to bring the

oil level up to, but not over, the full or OK range.

NOTE: Adding 0.95 liters (1 quart) of engine oil will raise the level from the add mark to the

top of the OK range.

All Models

Capacity

Fluid Type

Engine Oil (With Filter)

8.5 liters

(9 U.S. Quart)

Mercury/Quicksilver Synthetic Blend MerCruiser Engine Oil

25W‑40

7. Start the engine, run the engine for three minutes, and check for leaks. Stop the engine.

Allow approximately 5 minutes for the oil to drain into the oil pan. The boat must be at

rest in the water.

Power Steering Fluid

Checking

1. Stop the engine and center the sterndrive unit.
2. Remove the fill cap/dipstick from the power steering pump reservoir and observe the

level.
a.

Proper fluid level with engine at normal operating temperature should be within

the warm range.

Proper fluid level with engine cold should be within the cold range.

8484

a -

Power steering pump reservoir

b -

Cold range

c -

Warm range

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands