MerCruiser 496 MAG Bravo User Manual Download Page 105

Page: 105 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 97

3. Torque the propeller nut.

b c

5301

Typical Bravo One models

a -

Propeller shaft splines

b -

Forward thrust hub

c -

Flo‑Torque II drive hub

d -

Propeller

e -

Drive sleeve adapter

f -

Tab washer

g -

Propeller nut

d e

f g

19816

Bravo One XR models

a -

Propeller shaft

b -

Propeller hub insert with snubbers

c -

Propeller

d -

Thick washer

e -

Washer

f -

Washer

g -

Propeller nut

NOTE: The propeller torque stated is a minimum torque value.

Description

lb. in.

lb. ft.

Bravo One propeller nut

Then align tabs with grooves

NOTE: Bravo One XR models do not use the tab washer.

Models equipped with the tab washer

: Continue to tighten the propeller nut until the

3 tabs on the tab washer align with the grooves on the spline washer.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands