MerCruiser 496 MAG Bravo User Manual Download Page 5

Page: 5 / 146

90-864839061 NOVEMBER 2006

Page i

TABLE OF CONTENTS

Section 1 - Warranty

Warranty Registration: United States and

Canada....................................................................2

Warranty Registration: Outside the United States and

Canada....................................................................2

Transfer of Warranty................................................3

Mercury Product Protection Plan: United States and

Canada....................................................................3

Mercury MerCruiser Limited Warranty (Gasoline-

Fueled Products Only) ............................................4

3-Year Limited Warranty Against Corrosion............6

4-Year Limited Corrosion Warranty: SeaCore

Sterndrive Models with Gas Engines ......................7

Global Warranty Charts...........................................8

Consumer Application Warranty Chart...............8

Commercial Application Warranty Chart.............9

Government Application Warranty Chart..........10

Mercury Installation Quality Certification Program 10

California Emissions Limited Warranty..................11

What Is Covered...............................................11

Duration Of Coverage.......................................12

How To Obtain Warranty Coverage..................12

What Mercury Will Do.......................................13

What Is Not Covered........................................13

Components Of The Emission Control System 13

Disclaimers And Limitations..............................14

California Emission Control Warranty Statement. .14

Your Warranty Rights and Obligations.............14

Manufacturer's Warranty Coverage..................14

Owner's Warranty Responsibilities...................15

Emission Control Information Label.......................15

Owner Responsibility........................................16

Emission Certification Star Label...........................16

Section 2 - Getting to Know Your Power Package

Identification..........................................................20

Engine Serial Number Decal..........................20

Bravo Sterndrive Serial Number and

Identification...................................................20

Bravo Transom Serial Number.......................21

Lanyard Stop Switch..............................................22

Instrumentation......................................................23

System View.....................................................23

Digital Gauges..................................................24

Analog Gauges.................................................25

Remote Controls (Non-DTS Models).....................25

Remote Controls............................................25

Panel Mount Features..................................26

Console Mount Features..............................27

Zero Effort Features.......................................28

Remote Controls (DTS Models)............................28

Remote Controls............................................28

Panel Mount Features....................................29

Console Mount Features - Single Engine.......30

Slim Binnacle Console Mount Features - Single

Engine............................................................31

Console Mount Features- Dual Engine..........32

Synchronizing Dual Engines..........................33

Dual Helm Station Transfer............................33

Synchronizing Dual Helms Prior To Station

Transfer........................................................34

Zero Effort Features.......................................34

Power Trim............................................................35

Single Engine Trim/Trailer............................36

Dual Engine Trim/Trailer..............................36

Trim without Key.............................................36

Trim Delta.......................................................37

Electrical System Overload Protection..................37

Audio Warning System..........................................39

Testing The Audio Warning System.................40

Engine Guardian Strategy.....................................40

Warning Horn Signals............................................40

Section 3 - On The Water

Safe Boating Suggestions.....................................44

Be Alert To Carbon Monoxide Poisoning..............45

Good Ventilation...............................................46

Poor Ventilation ...............................................46

Basic Boat Operation (Non-DTS Models)..............46

Launching and Boat Operation.......................46

Operation Chart............................................47

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands