MerCruiser 496 MAG Bravo User Manual Download Page 91 | Manualshive

Page: 91 / 146

background image

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 83

2. Remove the IAC muffler.

a

18495

IAC muffler installed in the throttle body

a -

IAC muffler

3. Inspect the IAC muffler for damage such as, holes, cracks or deterioration. Replace

the IAC muffler if damaged.

IMPORTANT: Do not use cleaner containing methyl ethyl ketone.
IMPORTANT: Do not get cleaner on electrical connections.
4. Clean or replace the IAC muffler if grey or black, as the muffler should be white.
5. Clean the IAC muffler with warm water and a mild detergent.
6. Allow the IAC muffler to completely air dry before use.
7. Reinstall the IAC muffler.

Water‑Separating Fuel Filter (496)

Water‑Separating Fuel Filter

!

WARNING

Avoid serious injury or death from a gasoline fire or explosion; gasoline is extremely

flammable and highly explosive under certain conditions. When servicing the fuel system

components ensure that the engine is cool, the ignition switch is in the off position, and

that the lanyard stop switch, if equipped, is in the off position. Do not smoke or allow

spark or open flame in the area. Wipe up any spilled fuel immediately. Ensure that no

fuel leaks exist before closing the engine hatch.

!

WARNING

Avoid serious injury or death caused by fire or explosion. The fuel system is pressurized

during operation. Use care when removing the fuel filter. Fuel could spray on the hot

engine causing fire or explosion. Allow the engine to cool down and relieve fuel system

pressure before attempting to remove the fuel filter.

«
...
89
90
91
92
93
...
»

Summary of Contents for 496 MAG Bravo



















































































































































Reviews:

No comments

Related manuals for 496 MAG Bravo

EC FSE 400 - SERVICE 2002 & 2003

Brand: GAS GAS Pages: 74

Brand: Aerovent Pages: 16

E-II SGM H Series

Brand: YASKAWA Pages: 408

Brand: SEW-Eurodrive Pages: 88

Brand: Kohler Pages: 4

Brand: ABB Pages: 13

Brand: Volvo Penta Pages: 114

Brand: Masport Pages: 14

Brand: Yanmar Pages: 35

Brand: MULTIPLEX modell Pages: 11

Brand: Briggs & Stratton Pages: 11

3.5-1200 - V1.8

Brand: MVVS Pages: 2

Brand: Ford Pages: 46

Brand: Associated Electrics Pages: 4

Brand: Nanni Pages: 175

Brand: KAMA Pages: 25

Brand: Cuyuna Pages: 51

Brand: California Air Tools Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands