MerCruiser 496 MAG Bravo User Manual Download Page 60

Page: 60 / 146

Section 3 - On The Water

Page 52

90-864839061 NOVEMBER 2006

5. Throttle only mode is deactivated by moving the control lever to the idle/neutral position.

Moving the control lever from the idle/neutral position to the idle/forward or idle/reverse

position without pressing the throttle only button will shift the unit into the chosen gear.

Trailering the Boat

Your boat can be trailered with the sterndrive unit in the up or down position. Adequate

clearance is required between the road and sterndrive when transporting.
If adequate road clearance is a problem, place the sterndrive unit in full trailer position and

support it with an optional trailer kit which is available from your authorized Mercury

MerCruiser dealer.

Freezing Temperature Operation

IMPORTANT: If the boat is operated during periods of freezing temperature, precautions

must be taken to prevent freeze damage to the power package. Damage caused by

freezing is not covered by Mercury MerCruiser Limited Warranty.

Drain Plug and Bilge Pump

The engine compartment in your boat is a natural place for water to collect. For this reason,

boats are normally equipped with a drain plug and/or a bilge pump. It is very important to

check these items on a regular basis to ensure that the water level does not come into

contact with your power package. Components on your engine will be damaged if

submerged. Damage caused by submersion is not covered by the Mercury MerCruiser

Limited Warranty.

Protecting People In The Water

While You Are Cruising

It is very difficult for a person in the water to take quick action to avoid a boat heading in

their direction, even at slow speeds.

21604

Always slow down and exercise extreme caution any time you are boating in an area where

there might be people in the water.
Whenever a boat is moving (even coasting) and the gear shift is in neutral, there is sufficient

force by the water on the propeller to cause the propeller to rotate. This neutral propeller

rotation can cause serious injury.

While Boat Is Stationary

WARNING

Stop your engine immediately whenever anyone in the water is near your boat. Serious

injury to the person in the water is likely if contacted by a rotating propeller, a moving

boat, a moving gearcase, or any solid device rigidly attached to a moving boat or

gearcase.

Shift into neutral and shut off the engine before allowing people to swim or be in the water

near your boat.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands