MerCruiser 496 MAG Bravo User Manual Download Page 117

Page: 117 / 146

Section 5 - Maintenance

90-864839061 NOVEMBER 2006

Page 109

Flushing Device

91‑44357Q 2

9192

Attaches to the water intakes; provides a fresh water

connection when flushing the cooling system or operating the

engine.

Dual Water Pick‑up Flush Gearcase Seal Kit

91‑881150K 1

9194

Blocks off the front water inlet holes on the dual water inlet

gearcases.

STERNDRIVE WATER PICKUPS

There are two types of water pickups available on Mercury MerCruiser sterndrives: dual

water, and side pickups. Dual water pickups require the flushing attachment (44357Q 2)

and the flush seal kit (881150K 1), and side pickups require the flushing attachment

(44357Q 2).

5752

5773

Dual Water Pickup

Side Pickup

NOTE: Flushing is needed only for salty, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

CAUTION

If flushing the engine with the boat in the water, seawater can flow into the engine causing

damage. The water inlet must be closed when flushing the engine.

1. On seawater cooled models: Proceed to Step 3. or Step 4.
2.

On Bravo closed cooled models using the sterndrive seawater inlet and a
through-hull or through-transom alternative water pickup:

Flushing water will need

to be supplied to only the sterndrive by taking the following steps to block, or disconnect

and block, the hose from the alternative seawater pickup pump inlet Y‑fitting.
a.

If equipped with a seacock, close the seacock in the hose from the alternative

water pickup.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands