MerCruiser 496 MAG Bravo User Manual Download Page 140

Page: 140 / 146

Section 7 - Troubleshooting

Page 132

90-864839061 NOVEMBER 2006

Insufficient Engine Temperature

Possible Cause

Remedy

Faulty thermostat.

Replace.

Low Engine Oil Pressure

Possible Cause

Remedy

Insufficient oil in crankcase.

Check and add oil.

Excessive oil in crankcase (causing it to become

aerated).

Check and remove required amount of oil. Check for

cause of excessive oil (improper filling).

Diluted or improper viscosity oil.

Change oil and oil filter, using correct grade and

viscosity oil. Determine cause for dilution (excessive

idling).

Battery Will Not Come Up On Charge

Possible Cause

Remedy

Excessive current draw from battery.

Turn off non‑essential accessories.

Alternator drive belt loose or in poor condition.

Replace and/or adjust.

Unacceptable battery condition.

Test battery, replace if necessary.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires

(especially battery cables). Clean and tighten faulty

connections. Repair or replace damaged wiring.

Faulty alternator

Test alternator output, replace if necessary.

Remote Control Operates Hard, Binds, Has Excessive Free‑play Or

Makes Unusual Sounds

Possible Cause

Remedy

Insufficient lubrication on shift and throttle linkage

fasteners.

Lubricate.

Obstruction in shift or throttle linkages.

Remove obstruction.

Loose or missing shift and throttle linkages.

Check all throttle linkages. If any are loose or missing,

see authorized Mercury MerCruiser dealer

immediately.

Shift or throttle cable kinked.

Straighten cable or have authorized Mercury

MerCruiser dealer replace cable if damaged beyond

repair.

Steering Wheel Turns Hard Or Jerky

Possible Cause

Remedy

Low power steering pump fluid level.

Check for leak. Refill system with fluid.

Drive belt loose or in poor condition.

Replace and/or adjust.

Insufficient lubrication on steering components. Lubricate.

Loose or missing steering fasteners or parts.

Check all parts and fasteners if any are loose or missing,

see authorized Mercury MerCruiser dealer immediately.

Contaminated power steering fluid.

See authorized Mercury MerCruiser dealer.

Summary of Contents for 496 MAG Bravo



















































































































































Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands

MerCruiser 496 MAG Bravo, User Manual

Search results

Summary of Contents for 496 MAG Bravo

Reviews:

Related manuals for 496 MAG Bravo

Brands by name

Popular brands